skip to Main Content

فرآیند بدیع بازپخت دو مرحله‌ای جدید برای بهبود خواص مکانیکی فولاد منگنز متوسط

عنوان انگلیسی: A novel two-step intercritical annealing process to improve mechanical properties of medium Mn steel
سال نشر: ۲۰۱۹
نویسنده: Bin Hu,Haiwen Luo
تعداد صفحه فارسی: ۲۳ – تعداد صفحه انگلیسی: ۱۴
دانشگاه: State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing, 100083, China b School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, 100083, China
نشریه: Process Safety and Environmental Protection
کیفیت ترجمه: ترجمه پلاس

چکیده

در این مقاله، ما یک فرآیند تابکاری بین بحرانی دو مرحله‌ای جدید را ارائه می‌دهیم، به عنوان مثال یک وقفه چند دقیقه‌ای در طول حرارت دهی به دنبال تابکاری بین بحرانی کوتاه، برای بهبود خواص مکانیکی فولاد منگنز متوسط بدون طولانی کردن دوره تابکاری بین بحرانی (‏IA)‏. بررسی‌های تجربی و شبیه‌سازی عددی برای بررسی وراثت ریزساختاری بین دو مرحله و تاثیر آن بر خواص کششی انجام شد. افزایش دمای انقطاع منجر به تغییر تدریجی منحنی جریان کشش از تسلیم ناپیوسته به تسلیم پیوسته با قدرت تسلیم پایین‌تر به دلیل بیشتر مارتنزیت { مارتنزیت، که به نام متالورژیست آلمان آدولف مارتنز (۱۸۵۰–۱۹۱۴) نامیده می‌شود، به شکل بسیار سختی از ساختار کریستالی فولاد گفته می‌شود اما می‌توان به هر ساختار بلوری که توسط استحاله ی بدون نفوذ به وجود آمده،[۱] گفته می‌شود؛ که شامل یک کلاس از مواد معدنی سخت که دارای دانه‌های کریستالی بشقاب یا توفال شکل هستند، می‌شود.} و آستنیت { آستنیت یا آهن فاز-گاما‌‌ (γ-Fe)) یک دگرشکلی فلزی و غیر-مغناطیسی از آهن یا یک محلول جامد از آهن و یک ماده آلیاژی دیگر است.[۱] در فولادهای کربنی آستنیت در بالای نقطه یو

Abstract

In this paper, we present a novel two-step intercritical annealing process, i.e. a-few-minute interruption during heating followed by a short intercritical annealing, to improve the mechanical properties of medium Mn steel without prolonging the intercritical annealing (IA) period. Both experimental investigations and numerical simulations were performed to investigate the microstructural inheritance between the two steps and its influence on the tensile properties. The increase of interruption temperature led to a gradual change of tensile flow curve from the discontinuous yielding to the continuous yielding at lower yield strength due to more martensite and less austenite formed after the IA at 670 °C. It is concluded that the two-step IA process can improve the mechanical properties of medium Mn steel when it is optimized, compared to the non-interrupted IA process. The strategy for optimizing this novel process is to carefully tailor cementite precipitates before annealing as the n
امتیاز شما:
(No Ratings Yet)
Back To Top